Built for every trade
Roofing takeoff software for pitched roofs, gutters and flashings
Roofers and roof plumbers quote from the roof plan: sheet or tile area, gutters, ridges, flashings, downpipes and penetrations. TrueScale™ measures each one on the PDF at the drawing's scale, and gives the true roof surface once you set the pitch.
Start free trial 30 days, every feature, no card
What roofers and roof plumbers measure, and why
- Roof area, because sheets and tiles are bought and priced by the square metre of roof surface. A pitched roof is bigger than its plan, so the pitch goes on the measurement, not on a calculator later.
- Gutters, fascias and box gutters as lengths. They are supplied and fixed by the metre, and a box gutter costs far more per metre than an eaves gutter, so they need separate totals.
- Ridges, valleys and flashings as lengths, because each has its own capping or flashing profile and its own time on the roof.
- Downpipes, skylights and roof penetrations as counts. Each one is an item with its own flashing, fittings and labour.
The Roofing and drainage tool set
11 tools, from Tool Shed > Trade sets... > Roofing and drainage:
| Tool | Measures | Starter spec |
|---|---|---|
| Roof sheet | area | Metal roof sheet |
| Gutter length | length | Quad gutter |
| Downpipes | count | 90 dia downpipe |
| Skylights | count | Skylight |
| Roof penetrations | count | Roof penetration |
| Roof tile area | area | Concrete roof tile |
| Ridge length | length | Ridge capping |
| Valley length | length | Valley gutter |
| Fascia length | length | Metal fascia |
| Flashing length | length | Apron flashing |
| Box gutter length | length | Box gutter |
Worked example
Worked example: Kestrel Lane Townhouses
Sheet A3.01, the roof plan at 1:50: three hip roofs in prefinished metal at 22.5 degrees, with a downpipe at each corner.
| Measured | Sheet | Quantity |
|---|---|---|
| Roof sheet area on plan, three roofs to the eaves line | A3.01 | 425.48 m² |
| Roof sheet area with the 22.5 degree pitch set | A3.01 | 460.53 m² |
| Gutter length, eaves all round | A3.01 | 154.08 m |
| Ridge length | A3.01 | 28.80 m |
| Downpipes | A3.01 | 12 |
Per townhouse that is 141.83 m² of plan and 153.51 m² of roof surface. The pitch adds 35.05 m² across the job, a little over 8 percent, which is the difference between a roof that is quoted right and one that runs short.
Each townhouse also has 51.36 m of gutter, 9.60 m of ridge and four downpipes. The ridge is level, so its plan length is its real length.
A fictional demo project, drawn to scale and measured in TrueScale.
Start free trial 30 days, every feature, no card
Common roofing and drainage takeoff mistakes
- Pricing the plan area. On this job the roof is 8 percent bigger than its plan. Set the pitch on the area as a pitch, an angle or a grade, and TrueScale shows the sloped surface area instead.
- Measuring the roof from the floor plan. A floor plan stops at the walls. The roof runs out to the eaves, so the roof plan outline is the one to measure.
- Taking hips and valleys off the plan. Hips and valleys slope as well as run, so their plan length is shorter than the real one.
- Counting downpipes on the roof plan only. Check the stormwater or hydraulic plan as well. That is where the drainage design sets how many downpipes there are and where they go.
- Leaving out the metre items. Apron flashings against walls, barge cappings and fascia are easy to forget when the area is the big number. Give each its own tool so it shows up in the total.
Standards and the NCC
Roofs are installed to the NCC and the standards it calls up, such as AS 1562.1 for metal sheet roofing, AS 2050 for roof tiles, and AS/NZS 3500.3 for gutters, downpipes and roof drainage. TrueScale measures what the drawings show; the specification and those standards set what goes on the roof.
Roofing and drainage takeoff questions
How do I get the true area of a pitched roof from a plan?
Measure the roof outline on the roof plan with the Roof sheet tool, then set the roof pitch on that area as a pitch, an angle or a grade. TrueScale shows the sloped surface area. On the Kestrel Lane demo roofs, 425.48 m² of plan is 460.53 m² of roof at 22.5 degrees.
Can I measure box gutters separately from eaves gutters?
Yes. The Roofing and drainage set has Gutter length and Box gutter length as separate tools, so each has its own total and its own rate.
Does it work for tiled roofs as well as metal?
Yes. Use Roof tile area for tiles and Roof sheet for metal, with Ridge length, Valley length and Fascia length for the edges. Every tool is an example you can rename and give your own rate.
Can I count downpipes and skylights on the same sheet?
Yes. Downpipes, Skylights and Roof penetrations are count tools, each with its own symbol. Click each one on the plan and the count and the marks stay together on the drawing.
Pay once. Own it
One licence has every feature, the Estimate panel and Excel links included. Pay once, own your licence, and take off on TrueScale for Mac too.
Mac: Apple silicon (M1 or newer), macOS 14 or later. Printing, OCR, email, spell check and Link for Excel aren't on Mac yet. What's different on Mac