Built for every trade

Flooring takeoff software for every floor finish

Flooring takeoffs are areas by finish: tile, carpet, vinyl and timber, with underlay, levelling and waterproofing below, and skirting, nosings and transition strips at the edges. TrueScale™ measures each finish room by room from the floor finishes plan.

Start free trial 30 days, every feature, no card

What flooring installers measure, and why

  • Each finish as its own area, because tile, carpet, vinyl and timber are bought and laid at different rates.
  • Underlay, levelling and waterproofing as areas, because they sit under the finish and are priced on their own.
  • Skirting, stair nosings and wall tiles as lengths, the wall tiles with a height.
  • Transition strips as counts, one at each doorway where the finish changes.

The Flooring tool set

11 tools, from Tool Shed > Trade sets... > Flooring:

ToolMeasuresStarter spec
Floor tilesareaPorcelain tile
CarpetareaCarpet and underlay
VinylareaSheet vinyl
Timber floorareaEngineered timber
Floor levelling areaareaLevelling compound
SkirtinglengthSkirting board
Transition stripscountDoor transition strip
Wall tileswall area (run x height)Ceramic wall tile
Waterproofing areaareaWaterproof membrane
Underlay areaareaUnderlay
Stair nosings lengthlengthStair nosing

Worked example

Worked example: Kestrel Lane Townhouses

Sheets A2.02 and A2.04, the ground and first floor layout plans at 1:50, with the finish of each room from the finishes schedule. Three townhouses.

MeasuredSheetQuantity
Engineered timberA2.02 + A2.04198.36 + 140.13 = 338.49 m²
CarpetA2.04113.94 m²
Porcelain floor tilesA2.02 + A2.0419.44 + 42.12 = 61.56 m²
VinylA2.02 + A2.043.15 + 13.32 = 16.47 m²
Skirting in living areas, bedrooms and hallsA2.02 + A2.04107.85 + 236.55 = 344.40 m

Per townhouse: 112.83 m² of timber, 37.98 m² of carpet, 20.52 m² of tile and 5.49 m² of vinyl. Every room carries its finish as its label, so the Markups List can be read against the schedule.

A fictional demo project, drawn to scale and measured in TrueScale.

Start free trial 30 days, every feature, no card

Common flooring takeoff mistakes

  • Not deciding what goes under joinery. Decide whether the floor runs under the kitchen island and robes, and measure it the same way every time.
  • One waste figure for the job. Tiles, planks and broadloom carpet waste differently. Allow waste per finish, not one number for everything.
  • Missing the layers below. Waterproofing and levelling go under the tiles and the timber. Measure them with Waterproofing area and Floor levelling area.
  • Forgetting transitions. Every doorway between two finishes needs a strip. Count them while you measure the rooms.

Standards and the NCC

Tiling follows AS 3958.1, wet area waterproofing AS 3740, resilient floors such as vinyl AS 1884, and carpet AS/NZS 2455.1.

Flooring takeoff questions

How do I measure floor areas from a PDF plan?

Set the sheet's scale, pick the tool for the finish, such as Floor tiles, Carpet, Vinyl or Timber floor, and click around each room. TrueScale shows the area of each and totals them by finish.

Can I keep each floor finish separate?

Yes. Every finish is its own tool, so the Markups List totals tile, carpet, vinyl and timber apart.

Can I measure wall tiles too?

Yes. Wall tiles is a wall run: draw it along the wall and type the tile height, and TrueScale gives the tiled area.

Set the scale on a finishes plan first

Pay once. Own it

One licence has every feature, the Estimate panel and Excel links included. Pay once, own your licence, and take off on TrueScale for Mac too.

Mac: Apple silicon (M1 or newer), macOS 14 or later. Printing, OCR, email, spell check and Link for Excel aren't on Mac yet. What's different on Mac